{"id":8524,"date":"2021-07-29T04:01:23","date_gmt":"2021-07-29T04:01:23","guid":{"rendered":"https:\/\/www.hiclover.com\/?p=8524"},"modified":"2021-07-29T04:11:28","modified_gmt":"2021-07-29T04:11:28","slug":"biohazard-waste-disposal-guidelines","status":"publish","type":"post","link":"https:\/\/www.hiclover.com\/backup\/biohazard-waste-disposal-guidelines\/","title":{"rendered":"biohazard waste disposal guidelines"},"content":{"rendered":"
\n
<\/p>\n
biohazard waste disposal guidelines <\/div>\n
1. The ground should be flat when install the incinerator. There should be 100cm at least between the incinerator <\/div>\n
and the walls on the two sides and the back, which is in convenient maintenance and repair.<\/div>\n
2． <\/div>\n
A), Place the incinerator main body(combustion chamber) and fixed with bolts and Asbestos tape.<\/div>\n
B), Place the wet scrubber system and fixed with bolts and Asbestos tape.<\/div>\n
C). Install chimneys and fixed with bolts, Asbestos tape and Steel Rope.<\/div>\n
D). Fix the incineration house roof.<\/div>\n
E). Fix burner, blower, wind tube, electric system, fuel system.<\/div>\n
3. Check the electric wire: the incinerator’s electric circuit should be linked with the ground wire to guard against current leakage.  The link-up of the electric wire should be checked carefully before starting the incinerator, in case of wrong link-up or leakage.<\/div>\n
<\/div>\n
4. Check of the fuel supply system: Except the Burner’s soft pipe which is used for the fuel flowing-in and flowing-back, all the rest pipes must use brass or steel pipe. No leakage is allowed at pipe junctions. Any leakage should be blocked in time.<\/div>\n
<\/div>\n
5. Install steel rope with the chimney, to avoid tilt by wind. <\/div>\n
<\/div>\n
6. Install net cover at the blower, to avoid sundries.<\/div>\n
<\/div>\n
7. If the fuel is Natural Gas with gas burner, please contact with local administration section and install gas supplier system.<\/div>\n
<\/div>\n
8. Crane or forklift is necessary when download\/upload\/install incinerator. <\/div>\n
<\/div>\n
9. Topped work house roof after installation.<\/div>\n
<\/div>\n
10.Get the video material: http:\/\/www.eclover.net\/category\/incinerator-video\/<\/div>\n

<\/font><\/font><\/div>\n


 <\/div>\n

<\/FONT> <\/p>\n

<\/font><\/div>\n
<\/font><\/FONT><\/font> <\/div>\n
Nanjing Clover Medical Technology Co.,Ltd.<\/font><\/div>\n
\n
incinerate<\/font><\/div>\n
china orders incinerators<\/font><\/div>\n
hospital waste disposal ppt<\/font><\/div>\n
safe waste incinerator company<\/font><\/div>\n
medical sharps disposal services in kenya<\/font><\/div>\n<\/div>\n

<\/p>\n\n <\/p>\n\n\n\n\n\n<\/FONT><\/COLGROUP> <\/p>\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
Items\/Model<\/font><\/td>\nTS10(PLC)<\/font><\/td>\nTS20(PLC)<\/font><\/td>\nTS30(PLC)<\/font><\/td>\nTS50(PLC)<\/font><\/td>\n<\/tr>\n
Burn Rate (Average)<\/td>\n10-20 kg\/hour<\/td>\n20-30 kg\/hour<\/td>\n30-50 kg\/hour<\/td>\n50-100 kg\/hour<\/td>\n<\/tr>\n
Control Mode<\/td>\nPLC Auto.<\/td>\nPLC Auto.<\/td>\nPLC Auto.<\/td>\nPLC Auto.<\/td>\n<\/tr>\n
Combustion Chamber<\/td>\n100L<\/td>\n210L<\/td>\n330L<\/td>\n560L<\/td>\n<\/tr>\n
Internal Dimensions<\/td>\n50x50x40cm<\/td>\n65x65x50cm<\/td>\n75x75x60cm<\/td>\n100x80x70cm<\/td>\n<\/tr>\n
Secondary Chamber<\/td>\n50L<\/td>\n110L<\/td>\n180L<\/td>\n280L<\/td>\n<\/tr>\n
Smoke Filter Chamber<\/td>\nDry Scrubber<\/td>\nDry Scrubber<\/td>\nDry Scrubber<\/td>\nDry Scrubber<\/td>\n<\/tr>\n
Feed Mode<\/td>\nManual<\/td>\nManual<\/td>\nManual<\/td>\nManual<\/td>\n<\/tr>\n
Voltage<\/td>\n220V<\/td>\n220V<\/td>\n220V<\/td>\n220V<\/td>\n<\/tr>\n
Power<\/td>\n0.75Kw<\/td>\n0.83Kw<\/td>\n0.99Kw<\/td>\n1.2Kw<\/td>\n<\/tr>\n
Diesel Oil Consumption (kg\/hour)<\/td>\nAve.8.4<\/td>\nAve.10.9<\/td>\nAve.13.3<\/td>\nAve.16.9<\/td>\n<\/tr>\n
Natural Gas Consumption (m3n\/hour)<\/td>\nAve.10.1<\/td>\nAve.13<\/td>\nAve.16<\/td>\nAve.20.2<\/td>\n<\/tr>\n
Temperature Monitor<\/td>\nYes<\/td>\nYes<\/td>\nYes<\/td>\nYes<\/td>\n<\/tr>\n
Temperature Protection<\/td>\nYes<\/td>\nYes<\/td>\nYes<\/td>\nYes<\/td>\n<\/tr>\n
Items\/Model<\/font><\/td>\nTS100(PLC)<\/font><\/td>\nTS150(PLC)<\/font><\/td>\nTS300(PLC)<\/font><\/td>\nTS500(PLC)<\/font><\/td>\n<\/tr>\n
Burn Rate (Average)<\/td>\n100-150 kg\/hour<\/td>\n150-200 kg\/hour<\/td>\n300-400 kg\/hour<\/td>\n500-600 kg\/hour<\/td>\n<\/tr>\n
Control Mode<\/td>\nPLC Auto.<\/td>\nPLC Auto.<\/td>\nPLC Auto.<\/td>\nPLC Auto.<\/td>\n<\/tr>\n
Combustion Chamber<\/td>\n1200L<\/td>\n1500L<\/td>\n2000L<\/td>\n3000L<\/td>\n<\/tr>\n
Internal Dimensions<\/td>\n120x100x100cm<\/td>\n150x100x100cm<\/td>\n170x120x100cm<\/td>\n210x120x120cm<\/td>\n<\/tr>\n
Secondary Chamber<\/td>\n600L<\/td>\n750L<\/td>\n1000L<\/td>\n1500L<\/td>\n<\/tr>\n
Smoke Filter Chamber<\/td>\nDry Scrubber<\/td>\nDry Scrubber<\/td>\nDry Scrubber<\/td>\nDry Scrubber<\/td>\n<\/tr>\n
Feed Mode<\/td>\nManual<\/td>\nManual<\/td>\nManual<\/td>\nManual<\/td>\n<\/tr>\n
Voltage<\/td>\n220V<\/td>\n220V<\/td>\n220V<\/td>\n220V<\/td>\n<\/tr>\n
Power<\/td>\n1.38Kw<\/td>\n1.69Kw<\/td>\n2.57Kw<\/td>\n4.88Kw<\/td>\n<\/tr>\n
Diesel Oil Consumption (kg\/hour)<\/td>\nAve.20.4<\/td>\nAve.24.2<\/td>\nAve.33<\/td>\nAve.44<\/td>\n<\/tr>\n
Natural Gas Consumption (m3n\/hour)<\/td>\nAve.24.5<\/td>\nAve.29<\/td>\nAve.39.6<\/td>\nAve.52.8<\/td>\n<\/tr>\n
Temperature Monitor<\/td>\nYes<\/td>\nYes<\/td>\nYes<\/td>\nYes<\/td>\n<\/tr>\n
Temperature Protection<\/td>\nYes<\/td>\nYes<\/td>\nYes<\/td>\nYes<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

<\/font><\/div>\n

<\/p>\n
A heat exchanger to pre-heat air destined for the primary chamber is not compulsory but recommended.  <\/div>\n
The combustion air systems and fans shall be designed to ensure high combustion efficiency and avoid a reducing (corrosive) atmosphere, <\/div>\n
incomplete burnout of the flue gases and related problems. It should also be possible to heat the primary air from 10°C to approximately 145°C, <\/div>\n
depending on the waste composition and moisture content. <\/div>\n
“The incinerator shall be designed and equipped to be installed, commissioned and operated in such a way as to prevent emissions into the air giving rise to significant ground-level air pollution; in particular, exhaust gases shall be discharged in a controlled fashion by means of a stack the height of which is calculated in such <\/div>\n
a way as to safeguard human health and the environment.<\/div>\n

<\/font><\/div>\n

<\/p>\n
The incinerator combustion chamber(s) should be designed for easy maintenance of all internal parts including the refractory and insulation. Materials used in <\/div>\n
the individual parts of the incinerator shall be heat resistance and also be protected against oxidation, corrosion, etc. <\/div>\n
The incinerator shell shall be made of mild steel with an adequate thickness for small units of between 3-6mm and larger units 5-10 mm depending on the construction part and painted externally with heat resistant aluminum paint suitable to <\/div>\n
withstand 250° C.  The outside surface temperature of the incinerator casing should not exceed 50° C above ambient<\/div>\n
 temperature and shall include a safety mesh around all hot surfaces. Cold face refractory lining of calcium silicate or <\/div>\n
superior material, minimum thickness 100 mm.  <\/div>\n
Combustion control system The incinerator units shall include a temperature based electronic combustion control <\/div>\n
system that utilizes temperature <\/div>\n
and other data to inform automated or programmed cycling through the standard burn cycle: pre-heat, burn with <\/div>\n
waste addition, burn completion, cool-down. The system shall be capable of varying auxiliary fuel and air supply in both combustion chambers to achieve <\/div>\n
optimum combustion conditions. As far as practicable, the incinerator shall be of a plug and play type for ease of installation and commissioning in remote locations. <\/div>\n
“The control system shall have a separate push button-based work station, which shall be located adjacent to the loading bay and protected from weather and impact damage. <\/div>\n
The system shall allow for rapid and straightforward intervention by the operator if the automatic system is not achieving the desired results during a burn cycle. <\/div>\n

<\/font><\/div>\n

<\/font><\/div>\n
<\/p>\n
HICLOVER Solution for Fighting COVID-19, with ISO9001\/CE Certification.<\/font><\/strong><\/span><\/span><\/span><\/span><\/span><\/span><\/span><\/span><\/span><\/span><\/div>\n
Medical Waste Incinerator & <\/strong>Auto Roll Air Filter(Air Purification)<\/strong><\/font><\/font><\/span><\/span><\/span><\/span><\/span><\/span><\/span><\/span><\/span><\/span><\/div>\n

<\/span><\/font><\/div>\n

<\/p>\n

\n
<\/font> <\/div>\n
\n
Mobile: +86-138139 31455(WhatsApp)<\/font><\/div>\n

<\/FONT><\/div>\n

Website: <\/font>www.hiclover.com\/backup\/<\/font><\/a> <\/font><\/font><\/font><\/font> <\/font><\/font><\/font><\/font><\/font><\/font><\/font><\/font><\/font><\/font><\/font><\/font><\/font><\/div>\n
\n
\n
\n
Email:     <\/font>sales@hiclover.com<\/a><\/font><\/a>  <\/font><\/font><\/font><\/font><\/FONT><\/FONT><\/FONT><\/FONT><\/FONT><\/FONT><\/FONT><\/FONT><\/FONT>     <\/font><\/font><\/font><\/div>\n
Email:    <\/font>hicloversales@gmail.com<\/a><\/font><\/a>   <\/font><\/font><\/font><\/font> <\/font><\/font><\/font><\/font><\/FONT><\/FONT><\/FONT><\/div>\n<\/div>\n<\/div>\n<\/div>\n

<\/font><\/font><\/div>\n<\/div>\n\n\t\t