Incinerator 20 Kg
\nIncinerator electrically operated
\nincluding:
\n\uf0a7 A cage for receipt of biomedical waste;
\n\uf0a7 A combustion room with fireplace using a filter to retain ashes;
\n\uf0a7 A cover;
\n\uf0a7 An air supply;
\nA turbine \uf0a7 allowing supply air.
\n\uf0a7 \u25aa The incinerator should be a modern waste disposal unit, designed
\nto buttocks medical waste in a clean and environmentally efficient
\nmanner. It should use a temperature based logic control system
\nto provide optimum control of the working conditions and
\nincorporate a high capacity thermal oxidizing secondary room.
\n It should be designed to retain the exhaust gases, for at least two seconds to make sure the unit’s effective destruction of the combustion
\nproducts.
\n \u25aa All the incinerators to be provided and installed meet the
\nWaste Management Regulation 2006, legal notice No. 121 of
\n29th September 2006 and specifically 3rd schedule regulation
\n(26, 47) pertaining classification, standards, criteria, and
\nprocess for installing and operating incinerators.
\n \u25aa The capacity of the incinerator required should be to the
\nspecifications with a capacity to burn 100kgs\/Hr.
\n \u25aa The incinerator shall be run on a three-phase power supply
\n(mains).
\n \u25aa For the technical analysis, not only the treatment plant but
\nthe whole system will be considered. It will be the responsibility
\nof the Bidder to provide a full system, including all eventually
\nadditionally necessary secondary systems and additional
\nequipment.
\n \u25aa The machine offered shall be designed to function normally under
\nthe conditions of the purchaser’s country. The conditions include
\nPower Supply, Climate, Temperature, Humidity, etc.
\n\u25aa The Bidder must provide a guarantee for one year.
\n \u25aa All text, parameter etc. on all control working ports as
\nwell as on information screens and on print-outs will be in
\nEnglish language.
\n The Bidder shall provide all the essential documentation to be able to facilitate the legal requirements for the
\ninstallation and putting into use of their equipment. <\/p>\n
\u25aa Period of Execution is 90 days from contract signature for
\ndelivery to site and completion of verification operations
\nrequired for the issuance of provisional acceptance.
\n \u25aa Representatives of the Contracting Authority and the
\nBeneficiary, together with all the Bidder’s representative, shall
\nexecute the controls, testing and initial approval for provisional
\nand final approval. The provisional and final acceptance shall
\ntake place at the last destination.
\n \u25aa After-Sales Service: The Bidder is required to ensure that a
\nmaintenance, service and repair centre, which is approved by
\nthe Manufacturer, and which is able to quickly supply genuine
\nspare parts and consumables recommended by the Manufacturer
\nis available throughout the one year guarantee period. In
\nfulfillment of the condition with their offer, bidders must
\nsubmit a statement signed by the manufacturer or representative
\nof this manufacturer:
\n\u0366 Providing the name and address of its authorized
\nmaintenance, service and repair centre,
\n\u0366 Confirming that this authorized maintenance, service and
\nrepair facility is able to quickly supply genuine spare parts and
\nthe consumables recommended by the Manufacturer; and
\n\u25aa The Bidder will be responsible to deliver and install all
\nequipment provided to the hospitals in the
\nRepublic of Kenya. The Bidder shall deliver a time program within the whole construction and building period. The delivery
\nand installation time must be agreed between bidders, target
\nHospital and the Contracting Authority. The treatment plant must
\narrive pre-assembled. The Bidder shall make certain that all areas of
\nthe plant transported by sea will not be shipped as”deck
\ncargo”.
\n \u25aa It is anticipated that the Bidder cooperates closely with the
\ncontractor to the new waste handling building\/ housing and will
\nmake available all necessary technical information, drawing, etc. to
\nthe contractor.
\n . Waste Calorific Value 4000 KCAL\/Kg
\niv. Moisture content 10-25%
\nv. Estimated ash residue 5-10%
\nvi. Nominal capacity 100Kg\/hour batch load
\nvii. Secondary room 2 minutes @ 1100\u00b0C
\nviii. Environmental Environmental Management Coordination Act, 1999 and specifically, Waste management regulations, 2006
\n2 Equipment
\n2.1 Primary Combustion Chamber
\n\u25aa The primary combustion chamber is the main structure of the
\nincinerator, fabricated from mild steel plate and stiffened with
\nstainless steel sections. It’s carried from the floor level on a
\nsignificant steel support frame. Internally the shell is lined with
\ncalcium silicate insulation and a hot face mixture of superb duty brickwork or high strength castable.
\n \u25aa The main combustion chamber must ensure minimum exit
\ntemperature is less than 850\u00b0C.
\n One Manual Load Incinerator comprising:
\n\u25aa Manual Loading door (heavy duty steel door with proper refractory lining)
\n\u25aa Horizontal solid hearth, refractory lined main combustion
\nchamber. Approximate dimensions 800 mm diameters x 2100mm
\nlong
\n\u25aa Full sized bulk load\/ash removal door
\n\u25aa 1 off diesel-fired ignition burner — temperature controlled
\n\u25aa 1 off combustion air supply fan and distribution system, automatic
\ncontrol
\n\u25aa High capacity secondary combustion chamber with home time
\nless than two seconds @ >1100\u00b0C
\n\u25aa 1 off diesel-fired afterburner — temperature controlled
\n\u25aa Control panel — automatic operation
\n\u25aa Temperature indication primary and secondary chambers 0-
\n1200\u00b0C. Both chambers have to be insulated with refractory
\nmaterial (super duty 100mm thick firebrick with 25mm thick
\ncalcium silicate insulation)
\nNote: The secondary combustion chamber must be certain that the gas temperature as measured against the inner wall in the secondary room & not in the flame zone, isn’t less than 1100\u00b0C.
\n 2.2 Throughput
\n100kg\/hour in a minimal calorific value of 4,000 kcal\/kg and an average bulk density of I20kg\/ M3 for general waste and l60kg\/ M3 for healthcare waste.
\n 2.3 Ash
\nThe waste will be reduced by 90~95% to leave 10 -5% ash
\n2.4 Quality\/Environmental Standards
\n\u25aa Environment Management and Coordination Act, 1999
\n\u25aa BS3316
\n2.5 Operating Period
\n\u25aa Anticipated daily operating period 8 hours
\n\u25aa Maximum working period 12 hours
\n2.6 Chamber
\n\u25aa Should be refractory lined into the following standard; Hearth and
\nlower section of room walls
\n2.7 Hot face substance \u25aa Super duty firebrick
\n\u25aa Limiting continuous service limit 1500\u00b0C
\n\u25aa Thickness 100mm
\n\u25aa Thermal conductivity 1.3 W\/mk
\n2.8 Insulation
\n\u25aa Calcium silicate
\n\u25aa Limiting continuous service limit 1000\u00b0C
\n\u25aa Thickness 25mm
\n\u25aa Thermal conductivity 0.095 W\/mk
\n2.9 Chimney \/ Stack
\n\u25aa Must be manufactured from refractory lined mild steel or high
\nquality air-cooled stainless steel. The chimney\/stack should have a
\nminimum height of 10 meters above ground level.
\n \u25aa Refractory lined flanged chimney must be above the height of
\nany existing roof adjacent to the incinerator
\n\u25aa Provide lifting gear to hoist, erect and mount chimney, and
\nprovide supports slings as needed. \u25aa The chimney shall be painted with heat resistant
\npaint after installation.
\n 2.10 Ignition Burners
\nFully packed oil type, complete with electric ignition and flame failure controls, wired with continuous running fan and finish with all valves, fan and motor.
\n \u00b7 Maximum rating: at least 450kW\/hour
\n\u00b7 Burner: ordered for on\/off operation
\n\u00b7 Maximum consumption: at least 6 litres\/hour
\n\u00b7 Average consumption: at least 3 litres\/hour
\n2.11 Afterburner
\nFully packed oil type, complete with electric ignition and flame failure controls wired with continuous running fan and finish with all valves, fan and motor.
\n A mechanical
\nparticulate collector must be integrated after secondary
\ncombustion chamber for removal of particulate pollutants
\nentrained in the flue gas stream.
\n 2.13 Diesel Tank
\n\u25aa To provide for diesel services tank (Capacity 400 litres)
\nincluding level indicator
\n\u25aa The tank should be connected to the incinerator at higher level
\nto enable free-flow of diesel from the tank into the incinerator.
\n The connecting pipe must be a black pipe of accepted gauge
\nand diameter. Contain other accompanying accessories and
\naccessories \u25aa Connect leftovers to fuel supply.
\n 3 Documentation:
\nOperation manual 2 sets
\nService\/maintenance manual 2 sets
\n4 Certification
\n\u25aa National Environment Management Authority (NEMA)
\ncertification
\n5 Capacity to support equipment
\n\u25aa The agent\/supplier will have adequate facilities, spare parts,
\nconsumables and qualified and skilled technical personnel.
\n Installation works
\n\u25aa Provide lifting gears like forklift, gantry, rollers, and lifting
\njacks and position incinerator.
\n 6 Commissioning and Training
\n\u25aa The Agent will test all set operating parameters <\/p>\n
\u25aa The agent shall conduct a two days operation & maintenance
\ntraining to the Biomedical engineering personnel and incinerator
\noperators after installation & commissioning of the equipment.
\n 7 Commissioning Maintenance Contract
\n\u25aa Before the expiry of the guarantee \/ signing off, the provider shall
\nprovide a one-year replacement service parts (e.g. oil filters, air
\nfilters), the Quarterly regular maintenance price per quarter
\nfor three (3) quarters. <\/p>\n
Care control proposal.
\n \u25aa The maintenance contract price includes labour, transportation and
\naccommodation for the attending technicians. <\/p>\n
Maintenance control proposal.
\n\u25aa The maintenance contract price includes labour, transport and
\naccommodation for the attending technicians.<\/p>\n","protected":false},"excerpt":{"rendered":"
Incinerator 20 Kg Incinerator electrically operated including: \uf0a7 A cage for receipt of biomedical waste; \uf0a7 A combustion room with fireplace using a filter to retain ashes; \uf0a7 A cover; \uf0a7 An air supply; A turbine \uf0a7 allowing supply air. \uf0a7 \u25aa The incinerator should be a modern waste disposal unit, designed to buttocks medical […]<\/p>\n","protected":false},"author":1,"featured_media":2016,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_joinchat":[],"footnotes":""},"categories":[20],"tags":[],"class_list":["post-6146","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-waste-incinerator"],"aioseo_notices":[],"_links":{"self":[{"href":"https:\/\/www.hiclover.com\/backup\/wp-json\/wp\/v2\/posts\/6146","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.hiclover.com\/backup\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.hiclover.com\/backup\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.hiclover.com\/backup\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.hiclover.com\/backup\/wp-json\/wp\/v2\/comments?post=6146"}],"version-history":[{"count":1,"href":"https:\/\/www.hiclover.com\/backup\/wp-json\/wp\/v2\/posts\/6146\/revisions"}],"predecessor-version":[{"id":9057,"href":"https:\/\/www.hiclover.com\/backup\/wp-json\/wp\/v2\/posts\/6146\/revisions\/9057"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.hiclover.com\/backup\/wp-json\/wp\/v2\/media\/2016"}],"wp:attachment":[{"href":"https:\/\/www.hiclover.com\/backup\/wp-json\/wp\/v2\/media?parent=6146"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.hiclover.com\/backup\/wp-json\/wp\/v2\/categories?post=6146"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.hiclover.com\/backup\/wp-json\/wp\/v2\/tags?post=6146"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}