\uf0a7Finally, steam to\u00a0 the coat should shut off, the unloading door is to be opened <\/p>\n
\uf0a7Then the shaft and mixing arms are reversed to behave as unloading mechanism and should scoop the waste fragments out of <\/p>\n
the unloading door, onto a conveyor belt or directly into a waste container. <\/p>\n
\uf0a7The vessel should now be ready for another treatment cycle, having retained most of its heat to the treatment of the <\/p>\n
next batch. <\/p>\n
(B)Features and Specification of the Steam Boiler: <\/p>\n
Features of the Boiler: <\/p>\n
\uf0a7It must be an Electrical boiler <\/p>\n
\uf0a7Splash proof electric enclosure and switches <\/p>\n
\uf0a7Door Isolator to main electric enclosure <\/p>\n
\uf0a7Alarm lights and Safety\/protection against excel pressure <\/p>\n
\uf0a7Level control on feedback water tank <\/p>\n
Technical specification of the Boiler: <\/p>\n
\uf0a7Output: between: 90-110 kg\/h (F&A 100 deg C) <\/p>\n
\uf0a7Working pressure: between 7-10 bar <\/p>\n
\uf0a7Boiler water content: between 80-100 liter <\/p>\n
\uf0a7Feed water tank material: between 60-80 liter <\/p>\n
\uf0a7Power consumption: between 60-75 Kw <\/p>\n
\uf0a7Number of Heating Elements: 3-4 nos. <\/p>\n
\uf0a7Electrical requirements: 400Vac, 50 Hz, 3 ph <\/p>\n
(C)Technical Specifications of Tub washer <\/p>\n
Features: <\/p>\n
\uf0a7Fully automatic and manual modes. <\/p>\n
\uf0a7metallic construction, SA 240\/304 <\/p>\n
\uf0a7Sensors to maximize both system efficiency and operator safety. <\/p>\n
\uf0a7Must use Re-circulating cold wash water to minimize water consumption and operating costs <\/p>\n
\uf0a7Disinfects all bin surfaces <\/p>\n
\uf0a7Software Strong blow dryer to remove excess surface water <\/p>\n
\uf0a7has to be compliant with North American and EU regulations <\/p>\n
Specifications: <\/p>\n
\uf0a7Tub washer able to wash bins of a suitable size, the norm being 38 gram <\/p>\n
\uf0a7has to have an water reservoir of capacity minimum: 225 liter <\/p>\n
\uf0a7Perfectly suited to hospitals and clinics by processing up to min.300 bins per hour. <\/p>\n
\uf0a7Time to wash and dry one bin after loading-approximately 12 nos. <\/p>\n
\uf0a7Bins loading on wash station at a time -approximately 12 nos. <\/p>\n
\uf0a7Total length: approx 30.0 ft <\/p>\n
\uf0a7Total length: approx 8.0 ft <\/p>\n
\uf0a7Total length: approx 3.0-3.5 ft <\/p>\n
\uf0a7Height to Conveyer from floor: approx 3 feet. <\/p>\n
Drive of the Tub washer <\/p>\n
\uf0a7Motor driven <\/p>\n
\uf0a7Motor Horsepower: approx. 4.0 HP <\/p>\n
\uf0a7Power: 220vac, 1 ph or 400 VAC, 3 ph or to suit customer needs <\/p>\n
Bins to be included <\/p>\n
\uf0a7200 nos. With different color (depending on the actual requirement of the hospital) <\/p>\n
(D)Technical Specification of External SHREDDER Controls <\/p>\n
\uf0a7Pre-programmed PLC controlled <\/p>\n
\uf0a7Password activated and reversal history indication <\/p>\n
\uf0a7Motor starter with overload protection <\/p>\n
\uf0a7Automatic instantaneous stop on hard thing in shredder mattress <\/p>\n
\uf0a7Automatic heavy cutting load reversal and re-try , up to three times <\/p>\n
\uf0a7Control housing Nema Type 12 <\/p>\n
Cutting Hardwires <\/p>\n
\uf0a7Chamber Dimensions (W x L x H): approx. 33 cm x 38 cm x 25 cm <\/p>\n
\uf0a7Number of Knives: approx 18 or to match customer needs <\/p>\n
\uf0a7Knife Thickness: approx 18 mm or to suit customer needs <\/p>\n
\uf0a7Knife Diameter: approx 16 cm or to suit client needs <\/p>\n
\uf0a7Teeth per Knife: minimum 3 <\/p>\n
\uf0a7Number of Shafts: 2 ie double rotating shredder <\/p>\n
Drive of the shredder <\/p>\n
\uf0a7has to be motor driven <\/p>\n
\uf0a7Motor Horsepower: approx. 10 HP <\/p>\n
\uf0a7Motor RPM: minimum 1750 <\/p>\n
\uf0a7Speed Reduction: 60:1 <\/p>\n
\uf0a7Generated Torque: min 40 Nm or 350 Ibs\/in. <\/p>\n
\uf0a7Gearbox: should be Parallel shaft <\/p>\n
\uf0a7Shock Protection: Rubber Mount Torque Arm <\/p>\n
\uf0a7Power: 220vac, 1 ph\u00a0 or 400 VAC, Ph or to suit customer needs <\/p>\n
Ancillaries to be included <\/p>\n
\uf0a7Shredder stand, fabricated from 3″ sq. steel tubing, regular height 30 inches <\/p>\n
\uf0a7Shredder hopper, fabricated from 16 gauge steel, with optional switched hopper lid <\/p>\n
(E)Features & Technical Specification of Conveyer <\/p>\n
To carry processed waste from vessel to shredder <\/p>\n
Controls <\/p>\n
\uf0a7Motor starter with overload protection <\/p>\n
\uf0a7Control housing Nema Type 12 <\/p>\n
\uf0a7Safety pull-stops along either side of conveyer <\/p>\n
Ancillaries <\/p>\n
\uf0a7Conveyer stand, fabricated from 2″ sq. steel\u00a0 tube <\/p>\n
\uf0a7Raised sidewalls fabricated from 16 gauge steel <\/p>\n
Dimensions <\/p>\n
\uf0a7Over-all length: between 20-25 ft or proper length based on the setup requirement. <\/p>\n
\uf0a7Over-all width: between 24-30 inch <\/p>\n
\uf0a7Over-all height (without including stand): between 12-14 inch <\/p>\n
\uf0a7Available inclines:\u00a0\u00a0\u00a0 0-40 degrees <\/p>\n
\uf0a7Belt Speed: 75 ft\/min <\/p>\n
\uf0a7Dam spacing: approx. 16 inch <\/p>\n
Drive <\/p>\n
\uf0a7Motor driven <\/p>\n
\uf0a7Horsepower:approx. 0.75 HP <\/p>\n
\uf0a7Motor RPM: approx. 60 <\/p>\n
\uf0a7Electrical Power input: 220vac, 1phj or 400 VAC, 3 Ph or to suit customer needs <\/p>\n
(F)Technical Specification of Tipper <\/p>\n
Features: <\/p>\n
\uf0a7It is to be made to allow for effortless bin positioning beneath the door to unload processed waste and effortless <\/p>\n
maneuverability for lifting and tipping the waste to the shredder hopper. <\/p>\n
\uf0a7Equipped with 2 binds to adapt processed waste loads to be loaded to the shredder and shredder waste to be <\/p>\n
transported to the disposal bin. <\/p>\n
\uf0a7Frame: Rugged heavy duty frame constructed of formed and welded steel for extra strength <\/p>\n
\uf0a7Mast: Fabricated using cannel steel for greater strength and dependability. Open structure design complete with security <\/p>\n
cage to offer greater visibility. <\/p>\n","protected":false},"excerpt":{"rendered":"
\uf0a7Finally, steam to\u00a0 the coat should shut off, the unloading door is to be opened \uf0a7Then the shaft and mixing arms are reversed to behave as unloading mechanism and should scoop the waste fragments out of the unloading door, onto a conveyor belt or directly into a waste container. \uf0a7The vessel should now be ready […]<\/p>\n","protected":false},"author":1,"featured_media":2005,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_joinchat":[],"footnotes":""},"categories":[20],"tags":[],"class_list":["post-3796","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-waste-incinerator"],"aioseo_notices":[],"_links":{"self":[{"href":"https:\/\/www.hiclover.com\/backup\/wp-json\/wp\/v2\/posts\/3796","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.hiclover.com\/backup\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.hiclover.com\/backup\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.hiclover.com\/backup\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.hiclover.com\/backup\/wp-json\/wp\/v2\/comments?post=3796"}],"version-history":[{"count":0,"href":"https:\/\/www.hiclover.com\/backup\/wp-json\/wp\/v2\/posts\/3796\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.hiclover.com\/backup\/wp-json\/wp\/v2\/media\/2005"}],"wp:attachment":[{"href":"https:\/\/www.hiclover.com\/backup\/wp-json\/wp\/v2\/media?parent=3796"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.hiclover.com\/backup\/wp-json\/wp\/v2\/categories?post=3796"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.hiclover.com\/backup\/wp-json\/wp\/v2\/tags?post=3796"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}